Epoxy Primer Paints

Leading Manufacturers, Exporters and Wholesaler of 101 Epoxy Zinc Phosphate Primer, 102 Epoxy Zinc Chromate Primer, 103 Epoxy Red Oxide Zinc Chromate Primer, 104 Epoxy Zinc Phosphate Primer, 110 Grey Epoxy Zinc Phosphate Primer, 111 Epoxy Penetrating Primer, 112 Epoxy Zinc Rich Primer, 120 Epoxy Zp Steel Guard Primer, 121 Epoxy Hb Hs Mustic Primer, 130 Epoxy Finish Paint, 130M Epoxy Finish Paint and 151 Food Grade Epoxy Paint from Ahmedabad.

Business Type Manufacturer, Exporter, Supplier
Brand Name Saffro Mellow
Application By Brush / By Conventional Spray
Type Epoxy Zinc Phosphate Primer
Country of Origin India
Finish High Gloss,Matt
Packaging Type Plastic Bucket
Shade Grey
Solids By Volume 40 ± 3%
Theoretical Spreading Rate 13.33 sq.mt. / ltr. at recommended DFT of 30 µ
Flash Point Base : Above 23°C Hardener : Above 23°C
Drying Characteristics surface Dry : 60 90 Minutes
At 65% Relative Humidity & At 30°c Hard Dry : Overnight Full Cure : 7 Days
Shelf Life Base : 6 Months Hardener : 6 Months
Mixing Ratio Base : Hardener (as per Our Recommendations)
Thinner Epoxy Thinner 190
Pot Life 4 hours min at 30°C
Recommended Dft 30 - 40 µ.
Overcoating Interval Min : 8 Hours Max : 24 Hours
Compatibility Can Be Over Coated with Epoxy, Pu, Chlorinated Rubber and Oleo-resinous Topcoats.
Addition 10-15% & Max 5% if Required
Nozzle Orifice 1.2 -1.4 Mm & 0.37- 0.42mm
Nozzle Pressure 40-70 psi & 1400-1800 psi

Click to view more

Preferred Buyer From

Location Worldwide

Description

Two component Epoxy based anti corrosive primer pigmented with Zinc Chromate as corrosion inhibiting pigments.

Recommended Use :-

It is recommended as primer on M.S surface for original equipment manufacturing as well as for process industry as in various fertilizer, refineries, petrochemical, chemical and other plants, applied in diverse areas of tank exteriors, equipments, pipelines, structural steel, etc. Not to be used for immersion application.

Surface Preparation

Abrasive blasting to Sa 21/2 Swedish Standards is the best method of surface preparation. In case blasting is not possible, then the surface of steel should be cleaned to St-2/St-3 std. The surface should be absolutely dry, moisture and oil free before primer application.

Application Method

Stir the Base part thoroughly. Mix the base and hardener as per our recommended ratio, by volume. Stir the mix gently to attain homogeneity. Allow the mixture to stand still (maturation) for about 10-15 minutes to initiate the reaction. Add Epoxy Thinner into the mix, if required, depending on application method, and stir gently for few minutes. Strain the paint through Nylon filter cloth of 100 mesh size and apply uniformly over the surface. All equipments used for above should be properly cleaned.

Application :- By Brush / By Conventional Spray / By Airless Spray

Generally no thinner is required for Brush application, however under adverse environmental conditions about 5% of thinner, by volume, can be added. Apply evenly in criss-cross manner and ensure the uniform application. Use quality brushes for paint application.

Notes

1. Do not apply paint when temperature falls below 10°C or rises above 50°C and when Relative Humidity is above 85% or during rain, fog or mist. Surface temperature must always be minimum of 3°C above Dew point.

2. Brushes and spray equipment should be cleaned with SAFFRO's recommended thinner otherwise equipment is liable to be damaged.

3. DFT variation can be obtained by change in application method/thinning ratio.

4. Shelf life indicated is minimum for this Product in sealed conditions and it is subject to re-inspection thereafter. Individual component is required to be stored in cool, dry and covered condition, away from heat and ignition

Health & Safety

This is a solvent based paint and care should be taken to avoid inhalation of spray mist or vapours as well as contact between the wet paint and exposed skin or eyes.

Limitation of Liability

To the best of our knowledge, the technical data in our literature are true and accurate at the date of issuance but are subject to change without prior notice. We guarantee our product to conform to the specifications contained herein. We make no other warranty or guarantee of any kind, express or implied, including merchantability and fitness for particular purpose. Liability, if any, is limited to replacement of the product or refund of the purchased price. Labour or cost of labour and other consequential damages are hereby excluded.

 

Read More...


Yes! I am interested


Business Type Manufacturer, Exporter, Supplier
Brand Name Saffro Mellow
Application By Brush / By Conventional Spray / By Airless Spray
Type Epoxy Zinc Chromate Primer
State Liquid
Country of Origin India
Finish High Gloss, Matt
Packaging Type Plastic Bucket
Solids By Volume 40 ± 3%
Theoretical Spreading Rate 13.33 sq.mt. / ltr. at recommended DFT of 30 µ
Flash Point Base : 23°c Hardener : 23°c
Drying Characteristics Surface Dry : 60 to 90 Minutes
At 30°c & 65% Relative Humidity Hard Dry : Overnight. Full Cure : 7 Days
Shelf Life Base : 6 Months Hardener : 6 Months
Mixing Ratio Base : Hardener (As per our recommendation)
Thinner Epoxy Thinner 190
Pot Life 4 hours min at 30°C
Recommended Dft 30 - 40 µ.
Overcoating Interval Min : 8 Hours Max : 24 Hours
Compatibility Can Be Over Coated with Epoxy, Pu, Chlorinated Rubber and Oleo-resinous Topcoats.
Addition 10-15% & Max 5%
Nozzle Orifice 1.2 1.4 mm & 0.37- 0.42mm
Nozzle Pressure 40 - 70 p.s.i. & 1400-1800 p.s.i.

Click to view more

Preferred Buyer From

Location Worldwide

Description

Two component Epoxy based anti corrosive primer containing zinc phosphate as corrosion inhibiting pigments

Recommended Use :-

It is recommended as primer on M.S surface for OEM's as well as for process industries like fertilizers, refineries, chemicals and other plants. It can also be applied in diverse areas of tank exteriors, equipments, pipelines, structural steel, etc. Not to be used for immersion application.

Surface Preparation

Abrasive blasting to Sa 21/2 Swedish Standards is the best method of surface preparation. In case blasting is not possible, then the surface of steel should be cleaned to St-2/St-3 std. The surface should be absolutely dry, moisture and oil free before primer application.

Application Method

Stir the Base part thoroughly. Mix the base and hardener as per our recommended ratio, by volume. Stir the mix gently to attain homogeneity. Allow the mixture to stand still (maturation) for about 10-15 minutes to initiate the reaction. Add Epoxy Thinner into the mix, if required, depending on application method, and stir gently for few minutes. Strain the paint through Nylon filter cloth and apply uniformly over the surface. All equipments used for above should be properly cleaned. Application : By Brush / By Conventional Spray / By Airless Spray Generally no thinner is required for Brush application; however under adverse environmental conditions about 5% of thinner, by volume, can be added. . Apply evenly in crossed manner, ensuring the uniform application. Use quality brushes for paint application.

Notes

1. Do not apply paint when temperature falls below 10°C or rises above 50°C and when Relative Humidity is above 85%. Do not apply during rain, fog or mist. Surface temperature must always be minimum of 3°C above Dew point.

2. Brushes and spray equipment should be cleaned with SAFFRO's recommended thinner otherwise equipment is liable to be damaged.

3. DFT variation can be obtained by change in application method / thinning ratio.

4. Shelf life indicated is minimum for this Product in sealed conditions and it is subject to re-inspection thereafter. Individual component is required to be stored in cool, dry and covered condition, away from heat and ignition.

Health & Safety

This is a solvent based paint and care should be taken to avoid inhalation of spray mist or vapours as well as contact between the wet paint and exposed skin or eyes.

Limitation of Liability

To the best of our knowledge, the technical data in our literature are true and accurate at the date of issuance but are subject to change without prior notice. We guarantee our product to conform to the specifications contained herein. We make no other warranty or guarantee of any kind, express or implied, including merchantability and fitness for particular purpose. Liability, if any, is limited to replacement of the product or refund of the purchased price. Labour or cost of labour and other consequential damages are hereby excluded.

Read More...


Yes! I am interested


Business Type Manufacturer, Exporter, Supplier
Brand Name Saffro Mellow
Application By Brush / By Conventional Spray / By Airless Spray
Packaging Type Plastic Bucket
Type Red Oxide Zinc Chromate Primer
Shelf Life Base : 6 Months Hardener : 6 Months
Country of Origin India
Finish Matt
Solids By Volume 40 ± 3%
Theoretical Spreading Rate 13.33 sq.mt / lt at recommended DFT of 30 µ
Flash Point Base : Above 23° C Hardener : Above 23° C
Drying Characteristics (at 65% Relative Humidity & At 30°c) Surface Dry : 60 - 90 Minutes Hard Dry : Overnight Full Cure : 7 Days
Mixing Ratio Base : Hardener (As per our recommendations)
Thinner Epoxy Thinner 190
Pot Life At 30°c 4 Hours Min At 30°c
Recommended Dft 30 40 µ.
Overcoating Interval Min : 8 Hours Max : 24 Hours
Compatibility Can Be Over Coated with Epoxy, Pu, Chlorinated Rubber and Synthetic Enamel Finish Paints.
Addition 10-15% & Max 5% if Required
Nozzle Orifice 1.2 -1.4 Mm & 0.37- 0.42mm
Nozzle Pressure 40-70 p.s.i. & 1400-1800 p.s.i.

Click to view more

Preferred Buyer From

Location Worldwide

Description

Two component Epoxy based anti corrosive primer containing red oxide and zinc chromate as corrosion inhibiting pigments

Recommended Use :-

Recommended as a primer on suitably cleaned mild steel surface in various fertilizer units, refineries, chemical and other plants, transportation industries, steel plants, cement plants, power plants, pulp and paper industries, pharmaceutical industries, etc. for application on tank exteriors, structural steel, pipelines, machineries, vessels, etc. The product is recommended as a primer for mild to moderate service conditions. Not to be recommended for immersed water condition.

Surface Preparation

Abrasive blasting to Sa 21/2 Swedish Standards is the best method of surface preparation. In case blasting is not possible, then the surface of steel should be cleaned to St-2/St-3 std. The surface should be absolutely dry, moisture and oil free before primer application

Application Method

Stir the Base part thoroughly. Mix the base and hardener as per our recommended ratio, by volume. Stir the mix gently to attain homogeneity. Allow the mixture to stand still (maturation) for about 10-15 minutes to initiate the reaction. Add Epoxy Thinner into the mix, if required, depending on application method, and stir gently for few minutes. Strain the Application : By Brush / By Conventional Spray / By Airless Spray Generally no thinner is required for Brush application; however under adverse environmental conditions about 5% of thinner, by volume, can be added. Apply evenly in crossed manner, ensuring the uniform application. Use quality brushes for paint application.

Notes

1. Do not apply paint when temperature falls below 10°C or rises above 50°C and when Relative Humidity is above 85%. Do not apply during rain, fog or mist. Surface temperature must always be minimum of 3°C above Dew point.

2. Brushes and spray equipment should be cleaned with SAFFRO's recommended thinner otherwise equipment is liable to be damaged.

3. DFT variation can be obtained by change in application method/thinning ratio.

4. Shelf life indicated is minimum for this Product in sealed conditions and it is subject to re-inspection thereafter. Individual component is required to be stored in cool, dry and covered condition, away from heat and ignition.

Health & Safety

This is a solvent based paint and care should be taken to avoid inhalation of spray mist or vapours as well as contact between the wet paint and exposed skin or eyes.

Limitation of Liability

To the best of our knowledge, the technical data in our literature are true and accurate at the date of issuance but are subject to change without prior notice. We guarantee our product to conform to the specifications contained herein. We make no other warranty or guarantee of any kind, express or implied, including merchantability and fitness for particular purpose. Liability, if any, is limited to replacement of the product or refund of the purchased price. Labour or cost of labour and other consequential damages are hereby excluded.

Read More...


Yes! I am interested


Business Type Manufacturer, Exporter, Supplier
Brand Name Saffro Mellow
Application By Brush / By Conventional Spray
Type Epoxy Zinc Phosphate Primer
Country of Origin India
Finish Matt
Solids By Volume 40 ± 3%
Packaging Type Plastic Bucket
Theoretical Spreading Rate 13.33 sq.mt. / ltr. at DFT of 30 µ
Flash Point Base : Above 23°C Hardener : Above 23°C
Drying Characteristics (at 300 C & 65% Relative Humidity) Hard Dry : Overnight Full Cure : 7 Days
Shelf Life Base : 6 Months Hardener : 6 Months
Mixing Ratio Base : Hardener (As per our recommendations)
Thinner Epoxy Thinner 190
Pot Life 4 Hours Min At 30°c
Recommended Dft 30 - 40 µ.
Overcoating Interval Min : 8 Hours Max : 24 Hours
Compatibility Can Be Over Coated with Epoxy, Pu, Chlorinated Rubber and Synthetic Enamel Finish Paints.
Addition 10-15% & Max 5% if Required
Nozzle Orifice 1.2 -1.4 mm & 0.37- 0.42mm
Nozzle Pressure 40-70 p.s.i. & 1400-1800 p.s.i.

Click to view more

Preferred Buyer From

Location Worldwide

Description

Two component Epoxy based anticorrosive primer containing red oxide and zinc phosphate as corrosion inhibiting pigments

Recommended Use :-

This product is recommended as a primer on suitably cleaned mild steel surface in various fertilizer units, refineries, chemical and other plants, transportation industries, steel plants, cement plants, power plants, pulp and paper industries, pharmaceutical industries, etc. for application on tank exteriors, structural steel, pipelines, machineries, vessels, etc. The product is recommended as a primer for mild to moderate corrosion conditions. Not to be recommended for immersed water condition.

Surface Preparation

Abrasive blasting to Sa 21/2 Swedish Standards is the best method of surface preparation. In case blasting is not possible, then the surface of steel should be cleaned to St-2/St-3 std. The surface should be absolutely dry, moisture and oil free before primer application.

Application Method

Stir the Base part thoroughly. Mix the base and hardener as per our recommended ratio, by volume. Stir the mix, gently to attain homogeneity. Allow the mixture to stand still (maturation) for about 10-15 minutes to initiate the reaction.

Application : By Brush / By Conventional Spray / By Airless Spray Generally no thinner is required for Brush application; however under adverse environmental conditions about 5% of thinner, by volume, can be added. Apply evenly in crossed manner, ensuring the uniform application. Use quality brushes for paint application. Add Epoxy Thinner Thinner into the mix, if required, depending on application method, and stir gently for few minutes. Strain the paint through Nylon filter cloth and apply uniformly over the surface. All equipments used for above should be properly clean.

Notes

1. Do not apply paint when temperature falls below 10°C or rises above 50°C and when Relative Humidity is above 85%. Do not apply during rain, fog or mist. Surface temperature must always be minimum of 3°C above Dew point.

2. Brushes and spray equipment should be cleaned with SAFFRO's recommended thinner otherwise equipment is liable to be damaged.

3. DFT variation can be obtained by change in application method/thinning ratio.

4. Shelf life indicated is minimum for this Product in sealed conditions and it is subject to re-inspection thereafter. Individual component is required to be stored in cool, dry and covered condition, away from heat and ignition.

Health & Safety

This is a solvent based paint and care should be taken to avoid inhalation of spray mist or vapours as well as contact between the wet paint and exposed skin or eyes.

Limitation of Liability

To the best of our knowledge, the technical data in our literature are true and accurate at the date of issuance but are subject to change without prior notice. We guarantee our product to conform to the specifications contained herein. We make no other warranty or guarantee of any kind, express or implied, including merchantability and fitness for particular purpose. Liability, if any, is limited to replacement of the product or refund of the purchased price. Labour or cost of labour and other consequential damages are hereby excluded.

 

Read More...


Yes! I am interested


Business Type Manufacturer, Exporter, Supplier
Brand Name Saffro Mellow
Color Grey,Yellow,Beige,Red Oxide
Application By Brush / By Conventional Spray
Type Epoxy Zinc Phosphate Primer
State Liquid
Country of Origin India
Finish High Gloss
Packaging Type Plastic Bucket
Solids By Volume 48 ± 3% (Depends on shade)
Theoretical Spreading Rate Sq.mt / Lit At Recommended Dft of 30 Μ
Flash Point Base : Above 23°C Hardener : Above 23°C
Drying Characteristics (at 65% Relative Humidity & At 30°c) Dry to Handle: 3 Hr's Max Full Cure : 7 Days
Shelf Life Base : 6 Months Hardener : 6 Months
Mixing Ratio Base : Hardener (as per Our Recommendations)
Thinner Epoxy Thinner 190
Pot Life 4 Hours Min At 30°c
Recommended Dft 30 - 40 µ.
Overcoating Interval Min : 2 Hours Max : 24 Hours
Compatibility Can Be Over Coated with Epoxy, Pu, Chlorinated Rubber and Oleo-resinous Top Coats.
Addition 10-15% & Max 5% if Required.
Nozzle Orifice 1.2 -1.4 Mm & 0.37- 0.42mm
Nozzle Pressure 40-70 psi.& 1400-1800 psi.

Click to view more

Preferred Buyer From

Location Worldwide

Description

Two component Epoxy based anti corrosive primer containing zinc phosphate as corrosion inhibiting pigments

Recommended Use :-

It is an ideal primer where faster turnaround of equipment is desired, Hence making it ideal primer for industrial and Infrastructure equipments, heavy machineries etc exposed to medium corrosive and marine environment. It is also recommended for steel structures in Chemical, Fertilizers, Petrochemical and industrial plants. Not to be used for immersion application.

Surface Preparation

Abrasive blasting to Sa 21/2 Swedish Standards is the best method of surface preparation. In case blasting is not possible, then the surface of steel should be cleaned to St-2/St-3 std. The surface should be absolutely dry, moisture and oil free before primer application.

Application Method

Stir the Base part thoroughly. Mix the base and hardener as per our recommended ratio, by volume. Stir the mix gently to attain homogeneity. Allow the mixture to stand still (maturation) for about 10-15 minutes to initiate the reaction. Add Epoxy Thinner into the mix, if required, depending on application method, and stir gently for few minutes. Strain the paint through Nylon filter cloth of 100 mesh size and apply uniformly over the surface. All equipments used for above should be properly cleaned.

Application : By Brush / By Conventional Spray / By Airless Spray Generally no thinner is required for Brush application, however under adverse environmental conditions about 5% of thinner, by volume, can be added. Apply evenly in criss-cross manner and ensure the uniform application. Use quality brushes for paint application.

Notes

1. Do not apply paint when temperature falls below 10°C or rises above 50°C and when Relative Humidity is above 85% or during rain, fog or mist. Surface temperature must always be minimum of 3°C above Dew point.

2. Brushes and spray equipment should be cleaned with GP's recommended thinner otherwise equipment is liable to be damaged.

3. Products with Ld/Cr free version are available on requests.

4. Product for flow coat applications is also available on request.

5. DFT variation can be obtained by change in application method/thinning ratio.

6. Incase over coating interval exceeds the specified time duration than surface should be lightly scuffed with emery paper followed by solvent wipe.

7. Shelf life indicated is minimum for this Product in sealed conditions and it is subject to re-inspection thereafter. Individual component is required to be stored in cool, dry and covered condition, away from heat and ignition

Health & Safety

This is a solvent based paint and care should be taken to avoid inhalation of spray mist or vapours as well as contact between the wet paint and exposed skin or eyes.

Limitation of Liability

To the best of our knowledge, the technical data in our literature are true and accurate at the date of issuance but are subject to change without prior notice. We guarantee our product to conform to the specifications contained herein. We make no other warranty or guarantee of any kind, express or implied, including merchantability and fitness for particular purpose. Liability, if any, is limited to replacement of the product or refund of the purchased price. Labour or cost of labour and other consequential damages are hereby excluded.

Read More...


Yes! I am interested


Business Type Manufacturer, Exporter, Supplier
Brand Name Saffro Mellow
Application By Brush / By Conventional Spray / By Airless Spray
Type Epoxy Primers
State Liquid
Country of Origin India
Finish Smooth & Glossy
Solids By Volume 50 ± 3%
Theoretical Spreading Rate 20 sq.mt. / ltr. at a recommended DFT of 25 µ
Flash Point Base : Above 23°c Hardener : Above 23°c
Drying Characteristics (at 65% Relative Humidity & At 30°c) Hard Dry : Overnight Full Cure : 7 Days
Shelf Life Base : 6 Months Hardener : 6 Months
Mixing Ratio Base : Hardener - (As per our recommendations )
Thinner Epoxy Thinner 190
Pot Life 6 hours min at 30°C
Recommended Dft 25 - 30 Microns. Apply Sufficiently to Fill the Pores and Form a Thin Layer.
Overcoating Interval Min : 8 Hours Max : 24 Hours
Compatibility Compatible with Epoxy, Pu, and Chlorinated Rubber Finish
Addition 10-15% & Max 5% if Required
Nozzle Orifice 1.2 -1.4 Mm & 0.28 Mm - 0.38 Mm
Nozzle Pressure 40-70 p.s.i. & 1400-1800 p.s.i.

Click to view more

Preferred Buyer From

Location Worldwide

Description

Two component air drying Epoxy based clear primer with Polyamide as curing agent.

Recommended Use :-

This product is recommended as penetrating primer on bare concrete, wooden substrate prior to application of subsequent coating system.

Surface Preparation

Thorough surface preparation is vital. For best results, saffro recommends mechanical preparation techniques (Eg. mechanical scarifying, grit or sand sweeping),

 

a) New Concrete Surface :-

New concrete surface should be at least 28 days old and/or have moisture content of less than 5% before proceeding with primer application. Laitance and deposits on new concrete are best removed by light grit blasting, mechanical scarification or grinding. Acid etching may be considered for smaller areas, after etching the floor, it should be thoroughly washed with clean water, and then allowed to dry.

 

b) Old Concrete Floors :-

Mechanical cleaning methods are strongly recommended on old concrete surfaces, particularly their heavy contamination by oil and grease has occurred or old coatings is present. To ensure good adhesion, all contaminants are removed and the surface thoroughly cleaned of all dust and loose debris. A thorough detergent wash is also recommended followed by thorough cleaning with water and moping it off to a dry state.

Application Method

Stir the Base part thoroughly. Mix the base and hardener as per our recommended ratio, by volume. Stir the mix gently to attain homogeneity. Add Epoxy thinner into the mix, if required, depending on application method, and stir gently for few minutes. Allow the mixture to stand still (maturation) for about 10-15 minutes to initiate the reaction. Strain the paint through Nylon filter cloth of 200 mesh size and apply uniformly over the surface. All equipments used for above should be properly clean.

Application : By Brush / By Conventional Spray / By Airless Spray For Brush application, generally no thinner is required to be added. Apply uniformly in criss-cross manner and ensure there are no misses. Use quality brushes for paint application.

Notes

1. Do not apply paint when temperature falls below 10°C or rises above 50°C and when Relative Humidity is above 85%. Do not apply during rain, fog or mist. Surface temperature must always be minimum of 3°C above Dew point.

2. Brushes and spray equipment should be cleaned with SAFFRO's recommended thinner otherwise equipment is liable to be damaged.

3. DFT variation can be obtained by change in application method / thinning ratio.

4. Shelf life indicated is minimum for this Product in sealed conditions and it is subject to re-inspection thereafter. Individual component is required to be stored in cool, dry and covered condition, away from heat and ignition.

Health & Safety

This is a solvent based paint and care should be taken to avoid inhalation of spray or eyes. Mist or vapours as well as contact between the wet paint and exposed skin

Limitation of Liability

To the best of our knowledge, the technical data in our literature are true and accurate at the date of issuance but are subject to change without prior notice. We guarantee our product to conform to the specifications contained herein. We make no other warranty or guarantee of any kind, express or implied, including merchantability and fitness for particular purpose. Liability, if any, is limited to replacement of the product or refund of the purchased price. Labour or cost of labour and other consequential damages are hereby excluded.

Read More...


Yes! I am interested


Business Type Manufacturer, Exporter, Supplier
Brand Name Saffro Mellow
Application By Brush / By Conventional Spray / By Airless Spray
Type Epoxy Zinc Rich Primer
State Liquid
Categories Industrial
Country of Origin India
Finish Matt
Pack Type Bucket
Solids By Volume 50 ± 3%
Theoretical Spreading Rate 10 sq.mt / ltr at DFT of 50 µ
Flash Point Base : Above 23°C Hardener : Above 23°C
Drying Characteristics (at 30°c & At 65% Relative Humidity) Hard Dry : Overnight Full Cure : 7 Days
Shelf Life Base : 6 Months Hardener : 6 Months
Mixing Ratio Base : Hardener (as per Our Recommendations)
Thinner Epoxy Thinner 190
Pot Life 4 Hours Min At 30°c
Recommended Dft 30 50 µ.
Overcoating Interval Min : 8 Hours Max : Infinite
Compatibility Compatible with Epoxy, Pu, Chlorinated Rubber Intermediate/finish Coat.
Addition 10-15% & Max 5% if Required
Nozzle Orifice 1.2 -1.4 mm & 0.37- 0.42mm
Nozzle Pressure 40-70 psi. & 2100-2400 psi.

Click to view more

Preferred Buyer From

Location Worldwide

Description

Two component metallic zinc rich epoxy high performance primer.

Recommended Use :-

The zinc pigment in dry film renders excellent protection to steel structure, tanks, bullets, dam gates, pipelines, plant equipments, jetty, etc. in both interior and exterior exposed conditions of fertilizer units, chemical plants, steel plants, cement plants, pulp and paper industries, ports, power plants, petrochemical and pharmaceutical industry, transformer, machines & other heavy duty OEMs. It also provides cathodic protection to steel and gives good resistance to corrosion at local damaged areas. It is useful in heavy-duty protective paint systems. It is recommended not to expose the primed coat alone to chemical and saline atmosphere for a long time.

Surface Preparation

Abrasive blasting to minimum Sa 2 1/2 Standards is recommended with a profile of 35 - 75 microns. The surface should be absolutely dry and salt free before application. The primer should be applied preferably immediately or within 4 hours of blasting.

Application Method

Stir the Base part thoroughly with power stirrer. Mix the base and hardener as per our recommended ratio, by volume. Stir the mix gently to attain homogeneity. Add Epoxy Thinner into the mix, depending on application method, and stir gently for few minutes. Allow the mixture to stand still (maturation) for about 10-15 minutes to initiate the reaction. Strain the paint through Nylon filter cloth and apply uniformly over the surface. All equipments used for above should be properly clean.

Application: By Brush / By Conventional Spray / By Airless Spray Generally brushing is not recommended. However for small /touch up area with 5% max. Thinner addition it can be used. . Apply evenly in crossed manner ensuring uniform application. Use quality brushes for paint application.

Notes

1. Do not apply paint when temperature falls below 10°C or rises above 50°C and when Relative Humidity is above 85%. Do not apply during rain, fog or mist. Surface temperature must always be minimum of 3°C above Dew point.

2. Brushes and spray equipment should be cleaned with SAFFRO's recommended thinner otherwise equipment is liable to be damaged.

3. Products with different volume solids and Zinc contents are also available on requests.

4. Product for flow coat applications is also available on request.

5. DFT variation can be obtained by change in application method/thinning ratio.

6. Shelf life indicated is minimum for this Product in sealed conditions and it is subject to re-inspection thereafter. Individual component is required to be stored in cool, dry and covered condition, away from heat and ignition.

Health & Safety

This is a solvent based paint and care should be taken to avoid inhalation of spray mist or vapours as well as contact between the wet paint and exposed skin or eyes.

Limitation of Liability

To the best of our knowledge, the technical data in our literature are true and accurate at the date of issuance but are subject to change without prior notice. We guarantee our product to conform to the specifications contained herein. We make no other warranty or guarantee of any kind, express or implied, including merchantability and fitness for particular purpose. Liability, if any, is limited to replacement of the product or refund of the purchased price. Labour or cost of labour and other consequential damages are hereby excluded.

Read More...


Yes! I am interested


Business Type Manufacturer, Exporter, Supplier
Brand Name Saffro Mellow
Application By Brush / By Conventional Spray / By Airless Spray
Type Epoxy Primers
State Liquid
Country of Origin India
Finish Matt
Solids By Volume 63 + 3%
Theoretical Spreading Rate 8.4 sq.mt / lt at a recommended DFT of 75 µ
Flash Point Base : Above 25°c Hardener : Above 25°c
Drying Characteristics (at 30°c & 65% Relative Humidity) Hard Dry : 16 - 18 Hours Full Cure : 7 Days
Shelf Life Base: 6 Months Hardener: 6 Months
Mixing Ratio Base : Hardener (as per Our Recommendation )
Pot Life 2 Hours At 30°c
Thinner Epoxy Thinner 190
Recommended Dft 75-100 µ.
Overcoating Interval Min : 8 Hrs. Max : 24 Hours
Overcoatability Epoxy, Pu, Chlorinated Rubber and Synthetic Enamel Intermediate &finish Coat.
Addition 5-10% & Max 5% if Required
Nozzle Orifice 2 - 3 Mm & 0.48-0.53 Mm
Nozzle Pressure 40-70 P.s.i. & 2700-3200 Psi

Click to view more

Preferred Buyer From

Location Worldwide

Description

Two components, air drying, high build Epoxy primer. The product has the advantage of epoxy resin composition with specialty pigments, which facilitates one-coat, high build application for high performance. The product can be applied on minimum prepared surface and is designed to be completely wet and provide maximum intimacy with the substrate. Excellent adhesion is obtained on a variety of intact surfaces including over old coating and tightly adherent rust. With the high solids and less solvent content of the coating the risk of lifting, blistering, pin holing is reduced, and thus the risk of adhesion failure is minimized.

Recommended Use :-

It is recommended for steel structures in industrial plants, bridges, tank exteriors, oil tanks, pipes, marine atmosphere, cooling towers, etc. It has good resistance to spillage and fumes of acids, alkalis, fresh and salt water. Recommended as a primer on suitably cleaned mild steel surface in various Fertilizer units, Refineries, Chemical and other plants, Transportation industries, steel plants, cement plants, power plants, pulp and paper industries, pharmaceutical industries, etc. for application on tank exteriors, structural steel, pipelines, machineries, vessels, etc.

Surface Preparation

Abrasive blasting to Sa 21/2 Swedish Standards is the best method of surface preparation. In case blasting is not possible than manual cleaning by mechanical methods like wire brush, emery paper, hand / power tools, etc. to achieve St-2 / St-3 cleaning standards of Swedish specification. The surface should be free from moisture, oil, dust and dirt and should be absolutely dry before painting. Removal of loose rust is a must.

Application Method

Stir the Base part thoroughly. Mix the base and hardener in the recommended ratio by volume. Stir the mix thoroughly to attain homogeneity. Allow the mixture to stand still (maturation) for about 10 minutes to initiate the reaction. Add Epoxy Thinner into the mix, depending on application method, and stir thoroughly for few minutes. Strain the paint through Nylon filter cloth and apply uniformly over the surface. All equipments used for above should be properly cleaned.

Application: By Brush / By Conventional Spray/ By Airless Spray For Brush application, about 5-10% thinner is required to be added. Use quality brushes for paint application; Brushes made up of hog bristles are highly recommended. Size of the brush should be in proportion to the work in hand. Large size brushes (100-125 mm) for large areas and small brushes (25-50 mm) for narrow areas should be used

Notes

1. Do not apply paint when temperature falls below 10°C or rises above 50°C and when Relative Humidity is above 85%. Do not apply during rain, fog or mist. Surface temperature must always be minimum of 3°C above Dew point.

2. Brushes and spray equipment should be cleaned with SAFFRO's recommended thinner, otherwise equipment is liable to be damaged.

3. Products with MIO pigmentation and also with various amine Hardeners are available on requests

4. DFT variation can be obtained by change in application method / thinning ratio.

5. Product for flow coat applications is also available on request.

6. Shelf life indicated is minimum for this Product in sealed condition and it is subject to re-inspection thereafter. Individual component is required to be stored in cool, dry and covered condition, away from heat and ignition.

Health & Safety

This is a solvent based paint and care should be taken to avoid inhalation of spray mist or vapour as well as contact between the wet paint and exposed skin or eyes.

Limitation of Liability

To the best of our knowledge, the technical To the best of our knowledge, the technical data in our literature are true and accurate at the date of issuance but are subject to change without prior notice. We guarantee our product to conform to the specifications contained herein. We make no other warranty or guarantee of any kind, express or implied, including merchantability and fitness for particular purpose. Liability, if any, is limited to replacement of the product or refund of the purchased price. Labour or cost of labour and other consequential damages are hereby excluded.

Read More...


Yes! I am interested


Business Type Manufacturer, Exporter, Supplier
Brand Name Saffro Mellow
Application By Brush / By Conventional Spray / By Airless Spray
Type Epoxy Primers
State Liquid
Country of Origin India
Finish Semi Glossy
Solids By Volume 80 ± 2%
Theoretical Spreading Rate 10 sq.mt. / ltr. at a recommended DFT of 80 µ
Flash Point Base : Above 25°c Hardener : Above 25°c
Drying Characteristics (at 65% Relative Humidity & At 30°c) Surface Dry : 4 Hours Full Cure : 7 Days
Shelf Life Base : 6 Months Hardener : 6 Months
Mixing Ratio Base : Hardener ( As per our recommendations)
Thinner Epoxy Thinner 190
Recommended Dft 75-100 Mic.
Overcoating Interval Min : 8 Hours Max : 24 Hours
Compatibility Can Be Over Coated with Epoxy, Pu, Chlorinated Rubber and Oleo-resinous Topcoats.
Addition Max 10 - 15% & Max 5%, if Required.
Nozzle Orifice 2-3 mm & 0.53
Nozzle Pressure 40-70 psi. & 2700-3200.P.s.i

Click to view more

Preferred Buyer From

Location Worldwide

Description

Two component, air drying, high solids, Epoxy coating. The product has the advantage of epoxy resin composition with speciality pigment, which facilitates one-coat, high build application for high performance. The product can be applied on minimum prepared surface and is designed to completely wet the substrate. Excellent adhesion is obtained on a variety of intact surfaces including over old coating and tightly adherent rust. The composition has been balanced to a convenient mixing ratio by volume with excellent application characteristics. The low solvent content reduces the problem of lifting of the paint film and adhesion failure by blistering and pin holing. This assures a stable long term performance.

Recommended Use :-

It is mainly recommended in those areas where blasting is impractical or impossible. Uses include steel structures in Industrial plants, bridges, tank exteriors, oil tanks, pipes, marine atmosphere, cooling towers, etc. It has good resistance to spillage and fumes of acids, alkalis, fresh and salt water. Recommended as a primer on suitably cleaned mild steel surface in various Fertilizer units, Refineries, Chemical and other plants, Transportation industries, steel plants, cement plants, power plants, pulp and paper industries, pharmaceutical industries, etc. for application on tank exteriors, structural steel, pipelines, machineries, vessels, etc.

Surface Preparation

Abrasive blasting to Sa 21/2 Swedish Standards is the best method of surface preparation. In case blasting is not possible, then the surface of steel should be cleaned to St-2/St-3 std. The surface should be absolutely dry, moisture and oil free before primer application.

Application Method

Stir the Base part thoroughly. Mix the base and hardener as per our recommended ratio, by volume. Stir the mix gently to attain homogeneity. Allow the mixture to stand still (maturation) for about 10-15 minutes to initiate the reaction. Add EpoxyThinner into the mix, if required, depending on application method, and stir gently for few minutes. Strain the paint through Nylon filter cloth of 100 mesh size and apply uniformly over the surface. All equipments used for above should be properly cleaned.

Application: By Brush / By Conventional Spray / By Airless Spray Generally no thinner is required for Brush application, however under adverse environmental conditions about 5% of thinner, by volume, can be added. Apply evenly in criss-cross manner and ensure the uniformity. Use quality brushes for paint application.

Notes

1. Do not apply paint when temperature falls below 10°C or rises above 50°C and when Relative Humidity is above 85%. Do not apply during rain, fog or mist. Surface temperature must always be minimum of 3°C above Dew point.

2. Brushes and spray equipment should be cleaned with SAFFRO's recommended thinner otherwise equipment is liable to be damaged.

3. Products with different volume solids, MIO pigmented also with Amine Hardener are available on requests

4. DFT variation can be obtained by change in application method / thinning ratio.

5. Shelf life indicated is minimum for this Product in sealed condition and it is subjected to re-inspection thereafter. Individual component is required to store in cool, dry and covered condition, away from heat and ignition.

Health & Safety

This is a solvent based paint and care should be taken to avoid inhalation of spray mist or vapours as well as contact between the wet paint and exposed skin or eyes.

Limitation of Liability

To the best of our knowledge, the technical data in our literature are true and accurate at the date of issuance but are subject to change without prior notice. We guarantee our product to conform to the specifications contained herein. We make no other warranty or guarantee of any kind, express or implied, including merchantability and fitness for particular purpose. Liability, if any, is limited to replacement of the product or refund of the purchased price. Labour or cost of labour and other consequential damages are hereby excluded.

Read More...


Yes! I am interested


Business Type Manufacturer, Exporter
Brand Name Saffro Mellow
Application By Brush / By Conventional Spray / By Airless Spray
Type Epoxy Paints
State Liquid
Country of Origin India
Finish Glossy / Semi Glossy
Solids By Volume 40 ± 3% (Depends on shade)
Theoretical Spreading Rate 13.33 sq.mt / ltr at recommended DFT of 30 µ
Flash Point Base: Above 23° C Hardener: Above 23° C
Drying Characteristics (at 30°c and 65% Relative Humidity) Hard Dry : Overnight Full Cure : 7 Days
Shelf Life Base : 6 Months Hardener : 6 Months
Mixing Ratio Base : Hardener (As per our recommendation)
Thinner 190
Pot Life 4-6hrs min at 30 ° C
Recommended Dft 30-40 µ
Over Coating Interval Min : 8 Hours Max : 24 Hours
Compatibility Can Be Over Coated with Pu, Chlorinated Rubber and Synthetic Enamel Paints.
Addition 5 - 15% & Max 5%, if required.
Nozzle Orifice 1.2 -1.4 mm & 0.28 0.37 mm
Nozzle Pressure 40-70 p.s.i. & 1400-1800 p.s.i

Click to view more

Preferred Buyer From

Location Worldwide

Description

Two component, air-drying, Epoxy polyamide cured finish paint.

Recommended Use :-

It is recommended as a top coat for structures, pipelines, vessels, equipments and machineries, storage tanks etc. in fertilizers and chemical plant, cement plants, power plants, steel plants, pharmaceutical and petrochemical complexes, refineries etc. Product is also recommended for application over suitable primer for OEM industry like machine tools, pumps, machineries, transformers etc.

Surface Preparation

This being a topcoat, which is applied over, primer or intermediate coats, the surface should be free from oil, moisture, dust and dirt. Aged epoxy / PU coating should be roughened by emery paper grade 400 / 600 for better bonding.

Application Method

Stir the Base part thoroughly. Mix the base and hardener as per our recommended ratio, by volume. Stir the mix thoroughly to attain homogeneity. Allow the mixture to stand still (maturation) for about 10-15 minutes to initiate the reaction. Add Thinner Type 190 into the mix, if required, depending on application method, and stir thoroughly for few minutes. Strain the paint through Nylon filter cloth depending on type of finish selection and apply uniformly over the surface. All equipments used for above should be properly cleaned.

Application: By Brush / By Conventional Spray / By Airless Spray Generally for brush application no thinner is required, however under adverse environmental condition about 5% by volume thinner 002 can be added. Apply evenly in crossed manner, ensuring the uniform application. Use quality brushes for paint application

Notes

1. Do not apply paint when temperature falls below 10°C or rises above 50°C and when Relative Humidity is above 85%, or during rain, fog or mist. Surface temperature must always be minimum of 3°C above Dew point.

2. Brushes and spray equipment should be cleaned with SAFFRO's recommended thinner otherwise equipment is liable to be damaged.

3. DFT variation can be obtained by change in application method.

4. Shelf life indicated is minimum for this Product in sealed conditions and it is subject to re-inspection thereafter. Individual component is required to be stored in cool, dry and covered condition, away from heat and ignition.

5. Products with amine curing agent are also available on request.

Health & Safety

This is a solvent based paint and care should be taken to avoid inhalation of spray mist or vapours as well as contact between the wet paint and exposed skin or eyes.

Limitation of Liability

To the best of our knowledge, the technical To the best of our knowledge, the technical data in our literature are true and accurate at the date of issuance but are subject to change without prior notice. We guarantee our product to conform to the specifications contained herein. We make no other warranty or guarantee of any kind, express or implied, including merchantability and fitness for particular purpose. Liability, if any, is limited to replacement of the product or refund of the purchased price. Labour or cost of labour and other consequential damages are hereby excluded.

Read More...


Yes! I am interested


Business Type Manufacturer, Exporter, Supplier
Brand Name Saffro Mellow
Application By Brush / By Conventional Spray / By Airless Spray
Type Epoxy Paints
State Liquid
Country of Origin India
Finish Semi Glossy
Solids By Volume 40 ± 3% (Depends on shade)
Theoretical Spreading Rate 13.33 sq.mt / ltr at recommended DFT of 30 µ
Flash Point Base: Above 23° C Hardener: Above 23° C
Drying Characteristics Surface Dry : 90 Minutes Max Hard Dry : Overnight Full Cure : 7 Days
Shelf Life Base : 6 Months Hardener : 6 Months
Mixing Ratio Base : Hardener (as per Our Recommendation)
Thinner 190
Pot Life 4-6hrs min at 30 ° C
Recommended Dft 30-40 µ
Over Coating Interval Min : 8 Hours Max : 24 Hours
Compatibility Can Be Over Coated with Pu, Chlorinated Rubber and Synthetic Enamel Paints.
Addition 5 - 15% & Max 5%, if Required.
Nozzle Orifice 1.2 -1.4 Mm & 0.28 0.37 Mm
Nozzle Pressure 40-70 P.s.i. & 1400-1800 P.s.i

Click to view more

Preferred Buyer From

Location Worldwide

Description

Two component, air-drying, Epoxy polyamide cured finish paint.

Recommended Use :-

It is recommended as a top coat for structures, pipelines, vessels, equipments and machineries, storage tanks etc. in fertilizers and chemical plant, cement plants, power plants, steel plants, pharmaceutical and petrochemical complexes, refineries etc. Product is also recommended for application over suitable primer for OEM industry like machine tools, pumps, machineries, transformers etc.

Surface Preparation

This being a topcoat, which is applied over, primer or intermediate coats, the surface should be free from oil, moisture, dust and dirt. Aged epoxy / PU coating should be roughened by emery paper grade 400 / 600 for better bonding.

Application Method

Stir the Base part thoroughly. Mix the base and hardener as per our recommended ratio, by volume. Stir the mix thoroughly to attain homogeneity. Allow the mixture to stand still (maturation) for about 10-15 minutes to initiate the reaction. Add Thinner Type 190 into the mix, if required, depending on application method, and stir thoroughly for few minutes. Strain the paint through Nylon filter cloth depending on type of finish selection and apply uniformly over the surface. All equipments used for above should be properly cleaned.

Application: By Brush / By Conventional Spray / By Airless Spray Generally for brush application no thinner is required, however under adverse environmental condition about 5% by volume thinner 002 can be added. Apply evenly in crossed manner, ensuring the uniform application. Use quality brushes for paint application

Notes

1. Do not apply paint when temperature falls below 10°C or rises above 50°C and when Relative Humidity is above 85%, or during rain, fog or mist. Surface temperature must always be minimum of 3°C above Dew point.

2. Brushes and spray equipment should be cleaned with SAFFRO's recommended thinner otherwise equipment is liable to be damaged.

3. DFT variation can be obtained by change in application method.

4. Shelf life indicated is minimum for this Product in sealed conditions and it is subject to re-inspection thereafter. Individual component is required to be stored in cool, dry and covered condition, away from heat and ignition.

5. Products with amine curing agent are also available on request.

Health & Safety

This is a solvent based paint and care should be taken to avoid inhalation of spray mist or vapours as well as contact between the wet paint and exposed skin or eyes.

Limitation of Liability

To the best of our knowledge, the technical data in our literature are true and accurate at the date of issuance but are subject to change without prior notice. We guarantee our product to conform to the specifications contained herein. We make no other warranty or guarantee of any kind, express or implied, including merchantability and fitness for particular purpose. Liability, if any, is limited to replacement of the product or refund of the purchased price. Labour or cost of labour and other consequential damages are hereby excluded.

Read More...


Yes! I am interested


Business Type Manufacturer, Exporter, Supplier
Brand Name Saffro Mellow
Color Multicolor
Application By Brush / By Airless Spray
Type Food Grade Epoxy Paint
State Liquid
Country of Origin India
Finish Semi Glossy
Solids By Volume 80 ± 2%
Theoretical Spreading Rate 10 sq.mt. / ltr. at a recommended DFT of 80 µ
Flash Point Base : Above 25°C Hardener : Above 25°C
Drying Characteristics (at 65% Relative Humidity & At 30°c) Surface Dry : 4 Hours Full Cure : 7 Days Hard Dry : Overnight
Shelf Life Base : 6 Months Hardener : 6 Months
Mixing Ratio Base : Hardener (as per Our Recommendation)
Pot Life 2 - 3 hours min at 30° C
Recommended Dft 75-100 mic.
Overcoating Interval Min : 8 Hours Max : 24 Hours
Compatibility Can be over coated with Epoxy, PU
Addition Max 10 - 15% & Max 5%, if Required.
Nozzle Orifice 2-3 Mm & 0.48-0.53 Mm
Nozzle Pressure 40-70 psi. & 2700-3200.P.s.i

Click to view more

Preferred Buyer From

Location Worldwide

Description

Two component, air drying, high solids, Epoxy coating. The product has the advantage of epoxy resin composition with speciality pigment, which facilitates one-coat, high build application for high performance. The product can be applied on minimum prepared surface and is designed to completely wet the substrate. Excellent adhesion is obtained on a variety of intact surfaces including over old coating and tightly adherent rust. The composition has been balanced to a convenient mixing ratio by volume with excellent application characteristics. The ZERO solvent content reduces the problem of lifting of the paint film and adhesion failure by blistering and pin holing. This assures a stable long term performance.

Recommended Use :-

It is mainly recommended in those areas where blasting is impractical or impossible. Uses include steel structures in Industrial plants, bridges, tank exteriors, oil tanks, pipes, marine atmosphere, cooling towers, etc. It has good resistance to spillage and fumes of acids, alkalis, fresh and salt water. Recommended as a primer on suitably cleaned mild steel surface in various Fertilizer units, Refineries, Chemical and other plants, Transportation industries, steel plants, cement plants, power plants, pulp and paper industries, pharmaceutical industries, water tank, pipelines etc. for application on tank exteriors and interiors, structural steel, pipelines, machineries, vessels, etc.

Surface Preparation

Abrasive blasting to Sa 21/2 Swedish Standards is the best method of surface preparation. In case blasting is not possible, then the surface of steel should be cleaned to St-2/St-3 std. The surface should be absolutely dry, moisture and oil free before primer application.

Application Method

Stir the Base part thoroughly. Mix the base and hardener as per our recommended ratio, by volume. Stir the mix gently to attain homogeneity. Allow the mixture to stand still (maturation) for about 10-15 minutes to initiate the reaction. Add EpoxyThinner into the mix, if required, depending on application method, and stir gently for few minutes. Strain the paint through Nylon filter cloth of 100 mesh size and apply uniformly over the surface. All equipments used for above should be properly cleaned.

Application: By Brush / By Conventional Spray / By Airless Spray Generally no thinner is required for Brush application, however under adverse environmental conditions about 5% of thinner, by volume, can be added. Apply evenly in criss-cross manner and ensure the uniformity. Use quality brushes for paint application.

Notes

1. Do not apply paint when temperature falls below 10°C or rises above 50°C and when Relative Humidity is above 85%. Do not apply during rain, fog or mist. Surface temperature must always be minimum of 3°C above Dew point.

2. Brushes and spray equipment should be cleaned with SAFFRO's recommended thinner otherwise equipment is liable to be damaged.

3. Products with different volume solids, MIO pigmented also with Amine Hardener are available on requests

4. DFT variation can be obtained by change in application method / thinning ratio.

5. Shelf life indicated is minimum for this Product in sealed condition and it is subjected to re-inspection thereafter. Individual component is required to store in cool, dry and covered condition, away from heat and ignition.

Health & Safety

This is a solvent based paint and care should be taken to avoid inhalation of spray mist or vapours as well as contact between the wet paint and exposed skin or eyes.

Limitation of Liability

To the best of our knowledge, the technical data in our literature are true and accurate at the date of issuance but are subject to change without prior notice. We guarantee our product to conform to the specifications contained herein. We make no other warranty or guarantee of any kind, express or implied, including merchantability and fitness for particular purpose. Liability, if any, is limited to replacement of the product or refund of the purchased price. Labour or cost of labour and other consequential damages are hereby excluded.

Read More...


Yes! I am interested


Enquiry Now


Looking for Product Name ?

Close

Raise your Query

Hi! Simply click below and type your query.

Our experts will reply you very soon.

WhatsApp Us