PU Paints

Leading Manufacturers, Exporters and Wholesaler of 210 Intermediate Phosphate Primer, 211 Polyurethane Clear PU Paint, 231 Acrylic Polyurethane Topcoat PU Paint, 232 Hybrid Polyurethane Topcoat PU Paint, 241 Acrylic Aliphatic PU Finish Paint and 242 Hybrid Aliphatic PU Paint from Ahmedabad.

Business Type Manufacturer, Exporter, Supplier
Country of Origin India
Finish Egg Shell to Matt
Solids By Volume 40 ± 3%
Spreading Rate 13.3 Sq.mt / Ltr At Recommended Dft of 30 Μ
Flash Point Base : 23°c Hardener : 23°c
Drying Characteristics (at 30°c & 65% Relative Humidity) Surface Dry : 20-30 Minutes. Hard Dry : Overnight. Full Cure : 7 Days
SHELF LIFE BASE : 6 months HARDENER : 6 months
Mixing Ratio Base: Hardener ( as per Our Recommendation)
Application By Brush/ By Conventional Spray / By Airless Spray
Thinner Type 290
Pot Life 4 Hours Min At 30° C
Recommended Dft 30 -35 µ.
Overcoating Interval Min : 8 Hours Max : 24 Hours
Addition 5-15% & Max 5%, if required.
Nozzle Orifice 1.2-1.4mm & 0.28-0.37 mm
Nozzle Pressure 40-70 p.s.i & 1400-1800 p.s.i
Brand Name Saffro Mellow

Click to view more

Preferred Buyer From

Location Worldwide

Description

Two-component air-drying intermediate/primer surfacer coat.

Recommended Use :-

Recommended over putty / primer applied surfaces for better gloss retention and aesthetics in topcoats.

Surface Preparation

This being intermediate, it is applied either over primer. The surface should be free from moisture, oil and dust before application. In case of aged epoxy / PU coating or exceeded over coating, the surface should be sufficiently roughened prior to painting.

Application Method

Stir the Base part thoroughly. Mix the base and hardener as per our recommended ratio, by volume. Stir the mix thoroughly to attain homogeneity. Add Thinner Type 290 into the mix, if required, depending on application method, and stir thoroughly for few minutes. Allow the mixture to stand still (maturation) for about 10 minutes to initiate the reaction. Strain the paint through Nylon filter cloth and apply uniformly over the surface. All equipments used for above should be properly cleaned.

Application :- By Brush / By Conventional Spray / By Airless Spray

Generally no thinner is required for Brush application; however under adverse environmental conditions about 5% of thinner, by volume, can be added. Apply evenly in crossed manner and ensure the uniform application. Use quality brushes for paint application.

Notes

1. Do not apply paint when temperature falls below 10°C or rises above 50°C and when Relative Humidity is above 85%. Do not apply during rain, fog or mist. Surface temperature must always be minimum of 3°C above Dew point.

2. Brushes and spray equipment should be cleaned with SAFFRO's recommended thinner otherwise equipment is liable to be damaged.

3. DFT variation can be obtained by change in application method / thinning ratio.

4. Shelf life indicated is minimum for this Product in sealed conditions and it is subject to re-inspection thereafter. Individual component is required to be stored in cool, dry and covered condition, away from heat and ignition.

Health & Safety

This is a solvent based paint and care should be taken to avoid inhalation of spray mist or vapours as well as contact between the wet paint and exposed skin or eyes.

Limitation of Liability

To the best of our knowledge, the technical data in our literature are true and accurate at the date of issuance but are subject to change without prior notice. We guarantee our product to conform to the specifications contained herein. We make no other warranty or guarantee of any kind, express or implied, including merchantability and fitness for particular purpose. Liability, if any, is limited to replacement of the product or refund of the purchased price. Labour or cost of labour and other consequential damages are hereby excluded.

Read More...


Yes! I am interested


Business Type Manufacturer, Exporter, Supplier
Brand Name Saffro Mellow
Country of Origin India
Finish Smooth & Glossy
Solids By Volume 40 ± 3%
Theoretical Spreading Rate 16 sq.mt / ltr at a DFT of 25 µ
Flash Point Base : Above 23°C Hardener : Above 23°C
DRYING CHARACTERISTICS (At 65% Relative Humidity & at 30°C) HARD DRY : Overnight FULL CURE : 7 Days
Mixing Ratio Base : Hardener (as per Our Recommendations)
Thinner Type 290
Pot Life 3 Hours Min At 30° C
Recommended Dft 30-40 µ.
Overcoating Interval Min : 8 Hours Max : Indefinite
Addition 10-15% & Max 5%, if Required.
Nozzle Orifice 1.2 -1.4 mm & 0.28 mm
Nozzle Pressure 40-70 p.s.i.& 1400-1800 p.s.i.

Click to view more

Preferred Buyer From

Location Worldwide

Description

Two-component, air drying polyurethane based clear.

Recommended Use :-

This product is recommended Top coat for glossy , uv protection,weather property and also as penetrating primer on bare concrete, wooden substrate prior to application of subsequent coating system.

Surface Preparation

New concrete should be cured for at least 1 month prior to paint application. Ensure concrete surface is absolutely dry and free from moisture, oil, laitance, dust and dirt. For old concrete, ensure surface is free from oil, grease, algal & fungal growth and any old coating. Sand Blasting on concrete gives the best performance and should be given first preference out of the available surface preparation methods. If blasting is impracticable, Acid Etching with diluted Hydrochloric Acid followed by fresh water washing to be adopted. Seasoned wooden articles should be scuffed with Emery 220/400 to achieve smooth surface. Please refer our Directive Sheet on Surface Preparation.

Application Method

Stir the Base part thoroughly. Mix the base and hardener as per our recommended ratio, by volume. Stir the mix thoroughly to attain homogeneity. Add Thinner Type 290 into the mix, if required, depending on application method, and stir thoroughly for few minutes. Allow the mixture to stand still (maturation) for about 10 minutes to initiate the reaction. Strain the paint through Nylon filter cloth and apply uniformly over the surface. All equipments used for above should be properly cleaned.

Application :-By Brush / By Conventional Spray / By Airless Spray

Generally no thinner is required for Brush application, however under adverse environmental conditions about 5% of thinner, by volume, can be added. Use quality brushes for paint application. Brushes made up of hog bristles are highly recommended. Size of the brush should be in proportion to the work in hand. Large size brushes (100-125 mm) for large areas and small brushes (25-50 mm) for narrow areas should be used.

Notes

1. Do not apply paint when temperature falls below 10° C or rises above 50° C, when Relative Humidity is above 85% & during rain, fog, or mist. Do not apply on hot surface (above 50° C). Surface temperature must always be minimum of 3°C above Dew point.

2. Brushes and spray equipment should be cleaned with SAFFRO's recommended thinner otherwise equipment is liable to be damaged.

3. DFT variation can be obtained by change in application method / thinning ratio.

4. Shelf life indicated is minimum for this Product in sealed conditions and it is subject to re-inspection thereafter. Individual component is required to be stored in cool, dry and covered condition, away from heat and ignition.

Health & Safety

This is a solvent based paint and care should be taken to avoid inhalation of spray mist or vapours as well as contact between the wet paint and exposed skin or eyes.

Limitation of Liability

To the best of our knowledge, the technical data in our literature are true and accurate at the date of issuance but are subject to change without prior notice. We guarantee our product to conform to the specifications contained herein. We make no other warranty or guarantee of any kind, express or implied, including merchantability and fitness for particular purpose. Liability, if any, is limited to replacement of the product or refund of the purchased price. Labour or cost of labour and other consequential damages are hereby excluded.

Read More...


Yes! I am interested


Business Type Manufacturer, Exporter, Supplier
Brand Name Saffro Mellow
Application By Brush / By Conventional Spray / By Airless Spray
Country of Origin India
Colour Assorted Shades
Finish Glossy / Semi Glossy / Matt
Solids By Volume 40 ± 3% (depends On Shade)
Theoretical Spreading Rate 13.33 sq.mt / lt at recommended DFT of 30 µ
Flash Point Base : Above 23° C Hardener : Above 23° C
Drying Characteristics (at 30° C and 65% Relative Humidity) Surface Dry : 30 Minutes Max Hard Dry : Overnight Full Cure : 7 Days.
Shelf Life Base : 6 Months Hardener : 6 Months
Mixing Ratio Base : Hardener (as per Our Recommendation)
Pot Life 3 Hours Min At 30° C
Recommended Dft 30-40 µ.
Overcoating Interval Min : 8 Hours Max : 24 Hours
Compatibility Can Be Applied Over Epoxy and Polyurethane Primers, Intermediate Coats and Topcoats.
Thinner Type 290
Addition 5-15% & Max 5%, if Required.
Nozzle Orifice 1.2 -1.4 mm & 0.28 mm
Nozzle Pressure 1400-1800 p.s.i.

Click to view more

Preferred Buyer From

Location Worldwide

Description

Two component acrylic aromatic polyurethane finish coating

Recommended Use :-

This product is a topcoat along with recommended undercoats for use in chemical plants, fertilizer plants, petrochemical and pharmaceutical complex, power plants, cement plants, steel plants, heavy chemicals and off-shore and on-shore industries.

It is recommended for very high chemical resistance and for areas not exposed to direct sunlight. Product is also recommended for application over suitable primer for OEM industry.

Surface Preparation

The surface of primer or intermediate coats, over which this product is applied as topcoat, should be free from oil, moisture, dust and dirt. Aged coatings should be roughened by emery paper grade 400 / 600 for better bonding.

Application Method

Stir the Base part thoroughly. Mix the base and hardener as per our recommended ratio, by volume. Stir the mix gently to attain homogeneity. Add Thinner Type 290 into the mix, if required, depending on application method, and stir gently for few minutes. Allow the mixture to stand still (maturation) for about 10 minutes to initiate the reaction. Strain the paint through Nylon filter cloth of 400 mesh size and apply uniformly over the surface. All equipments used for above should

Application :-By Brush / By Conventional Spray / By Airless Spray

Generally no thinner is required for Brush application, however under adverse environmental conditions about 5% of thinner, by volume, can be added. Apply evenly in criss-cross manner, to ensure the uniform application. Use quality brushes for paint application.

Notes

1. Do not apply paint when temperature falls below 10°C or rises above 50°C and when Relative Humidity is above 85%, do not apply during rain, fog & mist. Surface temperature must always be minimum of 3°C above Dew point.

2. Brushes and spray equipment should be cleaned with SAFFRO's recommended thinner otherwise equipment is liable to be damaged.

3. Products with different volume solids, different qualities also available on requests.

4. DFT variation can be obtained by change in application method / thinning ratio.

5. Shelf life indicated is minimum for this Product in sealed conditions and it is subject to re-inspection thereafter. Individual component is required to be stored in cool, dry and covered condition, away from heat and ignition.

Health & Safety

This is a solvent based paint and care should be taken to avoid inhalation of spray mist or vapours as well as contact between the wet paint and exposed skin or eyes.

Limitation of Liability

To the best of our knowledge, the technical data in our literature are true and accurate at the date of issuance but are subject to change without prior notice. We guarantee our product to conform to the specifications contained herein. We make no other warranty or guarantee of any kind, express or implied, including merchantability and fitness for particular purpose. Liability, if any, is limited to replacement of the product or refund of the purchased price. Labour or cost of labour and other consequential damages are hereby excluded.

Read More...


Yes! I am interested


Business Type Manufacturer, Exporter, Supplier
Brand Name Saffro Mellow
Application By Brush / By Conventional Spray / By Airless Spray
Country of Origin India
Colour Assorted Shades
Finish Glossy / Semi Glossy / Matt Solids By
Volume 40 ± 3% (depends On Shade) Theoretical
Spreading Rate 13.33 Sq.mt / Lit At Recommended Dft of 30 µ
Flash Point Base : Above 23°C Hardener : Above 30°C
Drying Characteristics : Surface Dry :20 - 30 Minutes (at 30°c and 65% Relative Humidity) Hard Dry : Overnight Full Cure : 7 Days
Shelf Life Base : 6 Months Hardener : 6 Months
Mixing Ratio Base : Hardener (as per Our Recommendation)
Thinner Type 290
Pot Life 3 Hours Min At 30° C
Recommended Dft 30-40 µ.
Overcoating Interval MIN : 8 hours MAX :24 hours
Compatibility Can Be Applied Over Epoxy and Polyurethane Primers, Intermediate Coats and Topcoats
Addition 5 - 15% & Max 5%, if Required.
Nozzle Orifice 1.2 -1.4 mm & 0.28 mm
Nozzle Pressure 40-70 P.s.i. & 1400-1800 P.s.i.

Click to view more

Preferred Buyer From

Location Worldwide

Description

Two component air drying aromatic polyurethane finish coating

Recommended Use :-

It is recommended as topcoat for Original Equipment Machines, Hygienic, Maintenance painting where mild chemical resistance along with good abrasion resistance and decorative finish are required. Sometimes it is recommended as undercoat of finish coats application for economic benefits.

Surface Preparation

This being a Topcoat, which is applied over underneath primer or intermediate coats, the surface should be free from oil, moisture, dust and dirt. Aged coatings should be roughened by emery paper grade 400 / 600 followed by solvent wipe for better bonding.

Application Method

Stir the Base part thoroughly. Mix the base and hardener as per our recommended ratio, by volume. Stir the mix gently to attain homogeneity. Add Thinner Type 290 into the mix, if required, depending on application method, and stir gently for few minutes. Allow the mixture to stand still (maturation) for about 10minutes to initiate the reaction. Strain the paint through Nylon filter cloth 400 mesh size and apply uniformly over the surface. All equipments used for above should be properly cleaned.

Application :-By Brush / By Conventional Spray / By Airless Spray

Generally no thinner is required for Brush application, however under adverse environmental conditions about 5% of thinner, by volume, can be added. Apply evenly in crossed manner and ensure the uniformity. Use quality brushes for paint application.

Notes

1. Do not apply paint when temperature falls below 10°C or rises above 50°C and when Relative Humidity is above 85%, Do not apply during rain, fog, or mist. Surface temperature must always be minimum of 3°C above Dew point.

2. Brushes and spray equipment should be cleaned with SAFFRO's recommended thinner otherwise equipment is liable to be damaged.

3. Volume Solids will vary depending on shades. Products with different volume solids are also available on request.

4 DFT variation can be obtained by change in application method / thinning ratio.

5. Shelf life indicated is minimum for this Product in sealed conditions and it is subject to re-inspection thereafter. Individual component is required to be stored in cool, dry and covered condition, away from heat and ignition.

Health & Safety

This is a solvent based paint and care should be taken to avoid inhalation of spray mist or vapour as well as contact between the wet paint and exposed skin or eyes.

Limitation of Liability

To the best of our knowledge, the technical data in our literature are true and accurate at the date of issuance but are subject to change without prior notice. We guarantee our product to conform to the specifications contained herein. We make no other warranty or guarantee of any kind, express or implied, including merchantability and fitness for particular purpose. Liability, if any, is limited to replacement of the product or refund of the purchased price. Labour or cost of labour and other consequential damages are hereby excluded.

Read More...


Yes! I am interested


Business Type Manufacturer, Exporter, Supplier
Brand Name Saffro Mellow
Application By Brush / By Conventional Spray / By Airless Spray
Country of Origin India
Colour Industrial Shades
Finish Glossy / Semi-glossy
Solids By Volume 40 ± 3% (Depends on shade)
Theoretical Spreading Rate 13.33 sq.mt / ltr @ recommended DFT of 30 µ
Flash Point Base : Above 23°C Hardener : Above 23°C
Drying Characteristics (at 300 C & 65% Relative Humidity) Surface Dry : 30 Minutes Max Hard Dry : Overnight Full Cure : 7 Days
Shelf Life Base : 6 Months Hardener : 6 Months
Mixing Ratio Base: Hardener - as per Our Recommendations
Thinner Type 290
Pot Life 4 hours min at 30°C
Recommended Dft 30- 40 µ.
Overcoating Interval Min : 8 Hours Max : 24 Hours
Compatibility Can Be Applied Over Epoxy and Polyurethane Primers, Intermediate Coats and Topcoats.
Addition 5 - 15% & Max 5%, if required.
Nozzle Orifice 1.2 -1.4 mm & 0.28 - 0.37 mm
Nozzle Pressure 40-70 p.s.i & 1400-1800 p.s.i

Click to view more

Preferred Buyer From

Location Worldwide

Description

Two-component Air Drying Acrylic Aliphatic, Non Yellowing polyurethane finish coating.

Recommended Use :-

This product has excellent weathering resistance additionally it offers excellent resistance to various industrial chemical fumes and splash. This product is recommended as topcoat with suitable primers and undercoats for use in High Chemical & Saline atmosphere for better aesthetics and corrosion resistance in Chemical, Fertilizers, Petrochemical, industrial plants and also for premium industrial equipments. Not recommended for immersion application.

Surface Preparation

This being a topcoat, which is applied over, primer or intermediate coats, the surface should be free from oil, moisture, dust and dirt. Aged epoxy / PU coating should be roughened by emery paper grade 400 / 600 for better bonding.

Application Method

Stir the Base part thoroughly. Mix the base and hardener as per our recommended ratio, by volume. Stir the mix thoroughly to attain homogeneity. Allow the mixture to stand still (maturation) for about 10-15 minutes to initiate the reaction. Add Thinner Type 290 into the mix, if required, depending on application method, and stir thoroughly for few minutes. Strain the paint through Nylon filter cloth of 400 mesh size and apply uniformly over the surface. All equipments used for above should be properly cleaned.

Application :-By Brush / By Conventional Spray / By Airless Spray

Generally no thinner is required for Brush application, however under adverse environmental conditions about 5% of thinner, by volume, can be added. Apply evenly in criss-cross manner and ensure the uniform application. Use quality brushes for paint application.

Notes

1. Do not apply paint when temperature falls below 10°C or rises above 50°C and when Relative Humidity is above 85%. Do not apply during rain, fog or mist. Surface temperature must always be minimum of 3°C above Dew point.

2. Brushes and spray equipment should be cleaned with SAFFRO's recommended thinner otherwise equipment is liable to be damaged.

3. Products with different volume solids and for special applications like Flexible coating and anti fungal/anti bacterial versions are available on requests.

4. DFT variation can be obtained by change in application method / thinning ratio.

5. Shelf life indicated is minimum for this Product in sealed conditions and it is subject to re-inspection thereafter. Individual component is required to be stored in cool, dry and covered condition, away from heat and ignition.

Health & Safety

This is a solvent based paint and care should be taken to avoid inhalation of spray mist or vapours as well as contact between the wet paint and exposed skin or eyes.

Limitation of Liability

To the best of our knowledge, the technical data in our literature are true and accurate at the date of issuance but are subject to change without prior notice. We guarantee our product to conform to the specifications contained herein. We make no other warranty or guarantee of any kind, express or implied, including merchantability and fitness for particular purpose. Liability, if any, is limited to replacement of the product or refund of the purchased price. Labour or cost of labour and other consequential damages are hereby excluded.

Read More...


Yes! I am interested


Business Type Manufacturer, Exporter, Supplier
Brand Name Saffro Mellow
Application By Brush / By Conventional Spray / By Airless Spray
Country of Origin India
Colour Assorted Shades.
Finish Glossy / Semi-glossy / Matt Solids By
Volume 40 ± 3% (Depends on shade)
Theoretical Spreading Rate 15 sq.mt / ltr @ recommended DFT of 30 µ
Drying Characteristics (at 30°c & 65% Relative Humidity) Surface Dry : 70 - 80 Minutes Hard Dry : Overnight. Full Cure : 7 Days
Flash Point Base: Above 23° C Hardener: Above 23° C
Shelf Life Base : 6 Months Hardener : 6 Months
Mixing Ratio Base: Hardener (as per Our Recommendation)
THINNER Type 290
Pot Life 4 hours min at 30°C
Recommended Dft 30-40 µ.
Over Coating Interval Min : 8 Hours Max : 24 Hours
Compatibility Can Be Applied Over Epoxy and Polyurethane Primers, Intermediate Coats and Topcoats.
Addition 5 - 15% & Max 5% if Required
Nozzle Orifice 1.2 -1.4 mm & 0.28 - 0.37 mm
Nozzle Pressure 40-70 p.s.i. & 1400-1800 p.s.i.

Click to view more

Preferred Buyer From

Location Worldwide

Description

Two-component Air Drying acrylic aliphatic polyurethane finish coating.

Recommended Use :-

This product has excellent gloss, moderate colour retention and non-yellowing properties, against Ultraviolet rays and weathering, This product is recommended as topcoat with suitable primers and undercoats for use in moderate Chemical & Saline atmosphere for better aesthetics and corrosion resistance. It is recommended for Transportation Industries, Infrastructure Projects, locomotives, steel structure etc. is recommended as a self-priming coat for direct adhesion on variety of substrate like MS, Aluminum, Galvanized Iron and selected plastic surfaces.

Surface Preparation

This being a topcoat, which is applied over , primer or intermediate coats, the surface should be free from oil, moisture, dust and dirt. Aged epoxy / PU coating should be roughened by emery paper grade 400 / 600 for better bonding.

Application Method

Stir the Base part thoroughly. Mix the base and hardener as per our recommended ratio, by volume. Stir the mix gently to attain homogeneity. Add Thinner Type 290 into the mix, if required, depending on application method, and stir gently for few minutes. Allow the mixture to stand still (maturation) for about 10minutes to initiate the reaction. Strain the paint through Nylon filter cloth 400 mesh size and apply uniformly over the surface. All equipments used for above should be properly cleaned.

Application :-By Conventional Spray / By Airless Spray

Notes

1. Do not apply paint when temperature falls below 10°C or rises above 50°C and when Relative Humidity is above 85%. Do not apply during rain, fog, or mist. Surface temperature must always be minimum of 3°C above Dew point.

2. Spray equipment should be cleaned with SAFFRO's recommended thinner otherwise equipment is liable to be damaged.

3. Specific shades free from toxic pigment like Lead, Chrome, cadmium version is also available on request.

4. DFT variation can be obtained by change in application method / thinning ratio.

5. Shelf life indicated is minimum for this Product in sealed conditions and it is subject to re-inspection thereafter. Individual component is required to be stored in cool, dry and covered condition, away from heat and ignition.

Health & Safety

This is a solvent based paint and care should be taken to avoid inhalation of spray mist or vapours as well as contact between the wet paint and exposed skin or eyes.

Limitation of Liability

To the best of our knowledge, the technical data in our literature are true and accurate at the date of issuance but are subject to change without prior notice. We guarantee our product to conform to the specifications contained herein. We make no other warranty or guarantee of any kind, express or implied, including merchantability and fitness for particular purpose. Liability, if any, is limited to replacement of the product or refund of the purchased price. Labour or cost of labour and other consequential damages are hereby excluded.

Read More...


Yes! I am interested


Enquiry Now


Looking for Product Name ?

Raise your Query

Hi! Simply click below and type your query.

Our experts will reply you very soon.

WhatsApp Us