104 Epoxy Zinc Phosphate Primer

104 Epoxy Zinc Phosphate Primer

MOQ : 300 Litre

Business Type Manufacturer, Exporter, Supplier
Brand Name Saffro Mellow
Application By Brush / By Conventional Spray
Type Epoxy Zinc Phosphate Primer
Click to view more

Preferred Buyer From

Location Worldwide

Product Details

Country of Origin
India
Finish
Matt
Solids By Volume
40 ± 3%
Packaging Type
Plastic Bucket
Theoretical Spreading Rate
13.33 sq.mt. / ltr. at DFT of 30 µ
Flash Point
Base : Above 23°C Hardener : Above 23°C
Drying Characteristics (at 300 C & 65% Relative Humidity)
Hard Dry : Overnight Full Cure : 7 Days
Shelf Life
Base : 6 Months Hardener : 6 Months
Mixing Ratio
Base : Hardener (As per our recommendations)
Thinner
Epoxy Thinner 190
Pot Life
4 Hours Min At 30°c
Recommended Dft
30 - 40 µ.
Overcoating Interval
Min : 8 Hours Max : 24 Hours
Compatibility
Can Be Over Coated with Epoxy, Pu, Chlorinated Rubber and Synthetic Enamel Finish Paints.
Addition
10-15% & Max 5% if Required
Nozzle Orifice
1.2 -1.4 mm & 0.37- 0.42mm
Nozzle Pressure
40-70 p.s.i. & 1400-1800 p.s.i.

Description

Two component Epoxy based anticorrosive primer containing red oxide and zinc phosphate as corrosion inhibiting pigments

Recommended Use :-

This product is recommended as a primer on suitably cleaned mild steel surface in various fertilizer units, refineries, chemical and other plants, transportation industries, steel plants, cement plants, power plants, pulp and paper industries, pharmaceutical industries, etc. for application on tank exteriors, structural steel, pipelines, machineries, vessels, etc. The product is recommended as a primer for mild to moderate corrosion conditions. Not to be recommended for immersed water condition.

Surface Preparation

Abrasive blasting to Sa 21/2 Swedish Standards is the best method of surface preparation. In case blasting is not possible, then the surface of steel should be cleaned to St-2/St-3 std. The surface should be absolutely dry, moisture and oil free before primer application.

Application Method

Stir the Base part thoroughly. Mix the base and hardener as per our recommended ratio, by volume. Stir the mix, gently to attain homogeneity. Allow the mixture to stand still (maturation) for about 10-15 minutes to initiate the reaction.

Application : By Brush / By Conventional Spray / By Airless Spray Generally no thinner is required for Brush application; however under adverse environmental conditions about 5% of thinner, by volume, can be added. Apply evenly in crossed manner, ensuring the uniform application. Use quality brushes for paint application. Add Epoxy Thinner Thinner into the mix, if required, depending on application method, and stir gently for few minutes. Strain the paint through Nylon filter cloth and apply uniformly over the surface. All equipments used for above should be properly clean.

Notes

1. Do not apply paint when temperature falls below 10°C or rises above 50°C and when Relative Humidity is above 85%. Do not apply during rain, fog or mist. Surface temperature must always be minimum of 3°C above Dew point.

2. Brushes and spray equipment should be cleaned with SAFFRO's recommended thinner otherwise equipment is liable to be damaged.

3. DFT variation can be obtained by change in application method/thinning ratio.

4. Shelf life indicated is minimum for this Product in sealed conditions and it is subject to re-inspection thereafter. Individual component is required to be stored in cool, dry and covered condition, away from heat and ignition.

Health & Safety

This is a solvent based paint and care should be taken to avoid inhalation of spray mist or vapours as well as contact between the wet paint and exposed skin or eyes.

Limitation of Liability

To the best of our knowledge, the technical data in our literature are true and accurate at the date of issuance but are subject to change without prior notice. We guarantee our product to conform to the specifications contained herein. We make no other warranty or guarantee of any kind, express or implied, including merchantability and fitness for particular purpose. Liability, if any, is limited to replacement of the product or refund of the purchased price. Labour or cost of labour and other consequential damages are hereby excluded.

 

Yes! I am interested

Looking for "104 Epoxy Zinc Phosphate Primer" ?

Litre

Explore More Products


Raise your Query

Hi! Simply click below and type your query.

Our experts will reply you very soon.

WhatsApp Us