211 Polyurethane Clear PU Paint

211 Polyurethane Clear PU Paint

MOQ : 300 Litre

Business Type Manufacturer, Exporter, Supplier
Brand Name Saffro Mellow
Country of Origin India
Finish Smooth & Glossy
Click to view more

Preferred Buyer From

Location Worldwide

Product Details

Solids By Volume
40 ± 3%
Theoretical Spreading Rate
16 sq.mt / ltr at a DFT of 25 µ
Flash Point
Base : Above 23°C Hardener : Above 23°C
DRYING CHARACTERISTICS (At 65% Relative Humidity & at 30°C)
HARD DRY : Overnight FULL CURE : 7 Days
Mixing Ratio
Base : Hardener (as per Our Recommendations)
Type 290
Pot Life
3 Hours Min At 30° C
Recommended Dft
30-40 µ.
Overcoating Interval
Min : 8 Hours Max : Indefinite
10-15% & Max 5%, if Required.
Nozzle Orifice
1.2 -1.4 mm & 0.28 mm
Nozzle Pressure
40-70 p.s.i.& 1400-1800 p.s.i.


Two-component, air drying polyurethane based clear.

Recommended Use :-

This product is recommended Top coat for glossy , uv protection,weather property and also as penetrating primer on bare concrete, wooden substrate prior to application of subsequent coating system.

Surface Preparation

New concrete should be cured for at least 1 month prior to paint application. Ensure concrete surface is absolutely dry and free from moisture, oil, laitance, dust and dirt. For old concrete, ensure surface is free from oil, grease, algal & fungal growth and any old coating. Sand Blasting on concrete gives the best performance and should be given first preference out of the available surface preparation methods. If blasting is impracticable, Acid Etching with diluted Hydrochloric Acid followed by fresh water washing to be adopted. Seasoned wooden articles should be scuffed with Emery 220/400 to achieve smooth surface. Please refer our Directive Sheet on Surface Preparation.

Application Method

Stir the Base part thoroughly. Mix the base and hardener as per our recommended ratio, by volume. Stir the mix thoroughly to attain homogeneity. Add Thinner Type 290 into the mix, if required, depending on application method, and stir thoroughly for few minutes. Allow the mixture to stand still (maturation) for about 10 minutes to initiate the reaction. Strain the paint through Nylon filter cloth and apply uniformly over the surface. All equipments used for above should be properly cleaned.

Application :-By Brush / By Conventional Spray / By Airless Spray

Generally no thinner is required for Brush application, however under adverse environmental conditions about 5% of thinner, by volume, can be added. Use quality brushes for paint application. Brushes made up of hog bristles are highly recommended. Size of the brush should be in proportion to the work in hand. Large size brushes (100-125 mm) for large areas and small brushes (25-50 mm) for narrow areas should be used.


1. Do not apply paint when temperature falls below 10° C or rises above 50° C, when Relative Humidity is above 85% & during rain, fog, or mist. Do not apply on hot surface (above 50° C). Surface temperature must always be minimum of 3°C above Dew point.

2. Brushes and spray equipment should be cleaned with SAFFRO's recommended thinner otherwise equipment is liable to be damaged.

3. DFT variation can be obtained by change in application method / thinning ratio.

4. Shelf life indicated is minimum for this Product in sealed conditions and it is subject to re-inspection thereafter. Individual component is required to be stored in cool, dry and covered condition, away from heat and ignition.

Health & Safety

This is a solvent based paint and care should be taken to avoid inhalation of spray mist or vapours as well as contact between the wet paint and exposed skin or eyes.

Limitation of Liability

To the best of our knowledge, the technical data in our literature are true and accurate at the date of issuance but are subject to change without prior notice. We guarantee our product to conform to the specifications contained herein. We make no other warranty or guarantee of any kind, express or implied, including merchantability and fitness for particular purpose. Liability, if any, is limited to replacement of the product or refund of the purchased price. Labour or cost of labour and other consequential damages are hereby excluded.

Yes! I am interested

Looking for "211 Polyurethane Clear PU Paint" ?


Explore More Products

Raise your Query

Hi! Simply click below and type your query.

Our experts will reply you very soon.

WhatsApp Us