110 Grey Epoxy Zinc Phosphate Primer

300 Litre (MOQ)

Business Type Manufacturer, Exporter, Supplier
Brand Name Saffro Mellow
Color Grey,Yellow,Beige,Red Oxide
Application By Brush / By Conventional Spray
Click to view more

Preferred Buyer From

Location Worldwide

Product Details

Epoxy Zinc Phosphate Primer
Country of Origin
High Gloss
Packaging Type
Plastic Bucket
Solids By Volume
48 ± 3% (Depends on shade)
Theoretical Spreading Rate
Sq.mt / Lit At Recommended Dft of 30 Μ
Flash Point
Base : Above 23°C Hardener : Above 23°C
Drying Characteristics (at 65% Relative Humidity & At 30°c)
Dry to Handle: 3 Hr's Max Full Cure : 7 Days
Shelf Life
Base : 6 Months Hardener : 6 Months
Mixing Ratio
Base : Hardener (as per Our Recommendations)
Epoxy Thinner 190
Pot Life
4 Hours Min At 30°c
Recommended Dft
30 - 40 µ.
Overcoating Interval
Min : 2 Hours Max : 24 Hours
Can Be Over Coated with Epoxy, Pu, Chlorinated Rubber and Oleo-resinous Top Coats.
10-15% & Max 5% if Required.
Nozzle Orifice
1.2 -1.4 Mm & 0.37- 0.42mm
Nozzle Pressure
40-70 psi.& 1400-1800 psi.


Two component Epoxy based anti corrosive primer containing zinc phosphate as corrosion inhibiting pigments

Recommended Use :-

It is an ideal primer where faster turnaround of equipment is desired, Hence making it ideal primer for industrial and Infrastructure equipments, heavy machineries etc exposed to medium corrosive and marine environment. It is also recommended for steel structures in Chemical, Fertilizers, Petrochemical and industrial plants. Not to be used for immersion application.

Surface Preparation

Abrasive blasting to Sa 21/2 Swedish Standards is the best method of surface preparation. In case blasting is not possible, then the surface of steel should be cleaned to St-2/St-3 std. The surface should be absolutely dry, moisture and oil free before primer application.

Application Method

Stir the Base part thoroughly. Mix the base and hardener as per our recommended ratio, by volume. Stir the mix gently to attain homogeneity. Allow the mixture to stand still (maturation) for about 10-15 minutes to initiate the reaction. Add Epoxy Thinner into the mix, if required, depending on application method, and stir gently for few minutes. Strain the paint through Nylon filter cloth of 100 mesh size and apply uniformly over the surface. All equipments used for above should be properly cleaned.

Application : By Brush / By Conventional Spray / By Airless Spray Generally no thinner is required for Brush application, however under adverse environmental conditions about 5% of thinner, by volume, can be added. Apply evenly in criss-cross manner and ensure the uniform application. Use quality brushes for paint application.


1. Do not apply paint when temperature falls below 10°C or rises above 50°C and when Relative Humidity is above 85% or during rain, fog or mist. Surface temperature must always be minimum of 3°C above Dew point.

2. Brushes and spray equipment should be cleaned with GP's recommended thinner otherwise equipment is liable to be damaged.

3. Products with Ld/Cr free version are available on requests.

4. Product for flow coat applications is also available on request.

5. DFT variation can be obtained by change in application method/thinning ratio.

6. Incase over coating interval exceeds the specified time duration than surface should be lightly scuffed with emery paper followed by solvent wipe.

7. Shelf life indicated is minimum for this Product in sealed conditions and it is subject to re-inspection thereafter. Individual component is required to be stored in cool, dry and covered condition, away from heat and ignition

Health & Safety

This is a solvent based paint and care should be taken to avoid inhalation of spray mist or vapours as well as contact between the wet paint and exposed skin or eyes.

Limitation of Liability

To the best of our knowledge, the technical data in our literature are true and accurate at the date of issuance but are subject to change without prior notice. We guarantee our product to conform to the specifications contained herein. We make no other warranty or guarantee of any kind, express or implied, including merchantability and fitness for particular purpose. Liability, if any, is limited to replacement of the product or refund of the purchased price. Labour or cost of labour and other consequential damages are hereby excluded.

Yes! I am interested

Looking for "110 Grey Epoxy Zinc Phosphate Primer" ?


Explore More Products

Raise your Query

Hi! Simply click below and type your query.

Our experts will reply you very soon.

WhatsApp Us