120 Epoxy Zp Steel Guard Primer

120 Epoxy Zp Steel Guard Primer

MOQ : 300 Litre

Business Type Manufacturer, Exporter, Supplier
Brand Name Saffro Mellow
Application By Brush / By Conventional Spray / By Airless Spray
Type Epoxy Primers
Click to view more

Preferred Buyer From

Location Worldwide

Product Details

Country of Origin
Solids By Volume
63 + 3%
Theoretical Spreading Rate
8.4 sq.mt / lt at a recommended DFT of 75 µ
Flash Point
Base : Above 25°c Hardener : Above 25°c
Drying Characteristics (at 30°c & 65% Relative Humidity)
Hard Dry : 16 - 18 Hours Full Cure : 7 Days
Shelf Life
Base: 6 Months Hardener: 6 Months
Mixing Ratio
Base : Hardener (as per Our Recommendation )
Pot Life
2 Hours At 30°c
Epoxy Thinner 190
Recommended Dft
75-100 µ.
Overcoating Interval
Min : 8 Hrs. Max : 24 Hours
Epoxy, Pu, Chlorinated Rubber and Synthetic Enamel Intermediate &finish Coat.
5-10% & Max 5% if Required
Nozzle Orifice
2 - 3 Mm & 0.48-0.53 Mm
Nozzle Pressure
40-70 P.s.i. & 2700-3200 Psi


Two components, air drying, high build Epoxy primer. The product has the advantage of epoxy resin composition with specialty pigments, which facilitates one-coat, high build application for high performance. The product can be applied on minimum prepared surface and is designed to be completely wet and provide maximum intimacy with the substrate. Excellent adhesion is obtained on a variety of intact surfaces including over old coating and tightly adherent rust. With the high solids and less solvent content of the coating the risk of lifting, blistering, pin holing is reduced, and thus the risk of adhesion failure is minimized.

Recommended Use :-

It is recommended for steel structures in industrial plants, bridges, tank exteriors, oil tanks, pipes, marine atmosphere, cooling towers, etc. It has good resistance to spillage and fumes of acids, alkalis, fresh and salt water. Recommended as a primer on suitably cleaned mild steel surface in various Fertilizer units, Refineries, Chemical and other plants, Transportation industries, steel plants, cement plants, power plants, pulp and paper industries, pharmaceutical industries, etc. for application on tank exteriors, structural steel, pipelines, machineries, vessels, etc.

Surface Preparation

Abrasive blasting to Sa 21/2 Swedish Standards is the best method of surface preparation. In case blasting is not possible than manual cleaning by mechanical methods like wire brush, emery paper, hand / power tools, etc. to achieve St-2 / St-3 cleaning standards of Swedish specification. The surface should be free from moisture, oil, dust and dirt and should be absolutely dry before painting. Removal of loose rust is a must.

Application Method

Stir the Base part thoroughly. Mix the base and hardener in the recommended ratio by volume. Stir the mix thoroughly to attain homogeneity. Allow the mixture to stand still (maturation) for about 10 minutes to initiate the reaction. Add Epoxy Thinner into the mix, depending on application method, and stir thoroughly for few minutes. Strain the paint through Nylon filter cloth and apply uniformly over the surface. All equipments used for above should be properly cleaned.

Application: By Brush / By Conventional Spray/ By Airless Spray For Brush application, about 5-10% thinner is required to be added. Use quality brushes for paint application; Brushes made up of hog bristles are highly recommended. Size of the brush should be in proportion to the work in hand. Large size brushes (100-125 mm) for large areas and small brushes (25-50 mm) for narrow areas should be used


1. Do not apply paint when temperature falls below 10°C or rises above 50°C and when Relative Humidity is above 85%. Do not apply during rain, fog or mist. Surface temperature must always be minimum of 3°C above Dew point.

2. Brushes and spray equipment should be cleaned with SAFFRO's recommended thinner, otherwise equipment is liable to be damaged.

3. Products with MIO pigmentation and also with various amine Hardeners are available on requests

4. DFT variation can be obtained by change in application method / thinning ratio.

5. Product for flow coat applications is also available on request.

6. Shelf life indicated is minimum for this Product in sealed condition and it is subject to re-inspection thereafter. Individual component is required to be stored in cool, dry and covered condition, away from heat and ignition.

Health & Safety

This is a solvent based paint and care should be taken to avoid inhalation of spray mist or vapour as well as contact between the wet paint and exposed skin or eyes.

Limitation of Liability

To the best of our knowledge, the technical To the best of our knowledge, the technical data in our literature are true and accurate at the date of issuance but are subject to change without prior notice. We guarantee our product to conform to the specifications contained herein. We make no other warranty or guarantee of any kind, express or implied, including merchantability and fitness for particular purpose. Liability, if any, is limited to replacement of the product or refund of the purchased price. Labour or cost of labour and other consequential damages are hereby excluded.

Yes! I am interested

Looking for "120 Epoxy Zp Steel Guard Primer" ?


Explore More Products

Raise your Query

Hi! Simply click below and type your query.

Our experts will reply you very soon.

WhatsApp Us